How is satellite tv installed

Do not use existing cables such as RG as it may cause signal loss. Also, be sure that any outdoor connections are made using waterproof F-connectors rated for MHz or greater. The cable length between the DISH Damage caused by over-tightening is not covered by the limited warranty. Tighten all indoor coaxial cable connections to the receiver only by hand. If you use a wrench, you may over-tighten the connections and damage your equipment. Connect a temporary cable to a peaking meter. Thread the other end of the cable through the LNBF arm and bracket.

Attach the LNBFs to the bracket using the included screws. Do not adjust the skew. Ensure you are peaking the dish using transponder 11 or higher. With the peaking meter still connected, tighten the mast clamp and elevation bolts using the torque values listed in Table 1 on page 6.

Re-confirm signal strength after tightening the bolts. Remove the temporary cable used for peaking the dish. Thread the cable s from the receiver s through the LNBF arm and bracket. Connect a cable from DPP If a Legacy receiver is present, it should be installed last. Connect a cable from the DPP A splitter or other device will not work in this configuration.

If you use a wrench, you may over-tighten the connections and damage your equipment Connect the receiver s to the TV s and display the Point Dish screen if not shown, for most receivers, press MENU on the remote control.

Join Our Mailing List. Email Address:. Website design by Solid Cactus. All rights reserved. This image may not be used by other entities without the express written consent of wikiHow, Inc. Select a flat spot on or around your home. Find a level place that is accessible if you need to clean off or adjust the satellite dish later. If you have space, the safest place for a satellite dish is on the ground. It will have plenty of room to point north or south, depending on where you live.

Also, keep the dish away from falling snow or ice, such as from your roof or nearby trees. Try to find a spot close to them to make the wiring process easier. If you mount the dish on the ground, you will need to dig a trench to run its cables to your home safely.

Check for any obstructions blocking the dish's view of the sky. Stand where you plan on installing the dish. Look up to the sky. If you see buildings, trees, or even clotheslines in the way, then find another spot. These obstacles stop the dish from receiving a clear signal, affecting your picture quality. The rod gives the dish more height without it needing to be on the roof.

Satellite dish installers almost automatically go for the roof to guarantee the satellite isn't obstructed. You may need to do this, too, if you can't find an exact spot elsewhere. If you're in the northern hemisphere, the dish needs to point south to receive a signal. If you're in the southern hemisphere, it needs to point north, so keep that in mind when looking for obstacles.

Hold the dish's mount to your home and mark the screw positions. The dish's support is an L-shaped rod with a base plate that fastens to your home. Position the base plate flat against the wall or roof in the location you chose. Look for a series of holes on the plate for bolts. Then, use a permanent marker to note the position of these holes on the roof. Don't try to anchor it to siding since it won't hold.

Calculate the size of the pilot holes needed to secure the mount. The holes' exact size and depth depend on the dish you're installing, so reference the components that came with the satellite.

That number will tell you how wide the holes need to be. Create the pilot holes using a drill bit the same size as the mounting bolts. Use a masonry drill bit to break through stone and other rigid surfaces without damaging your drill. The bit needs to create holes that are the perfect size for the bolts. Drill into the spots you marked earlier once you are ready. Make sure the holes you create are straight, so the mounting bolts fit properly.

If they are too small, the bolts won't fit. Erring on the side of caution is better when drilling. You can always widen a small hole. Place the mount's metal plugs into the holes you drilled. Your dish will come with a set of metal plugs that serve as wall anchors. One end of each plug will have a bolt hole in it. Flip the plugs, so the openings face toward you rather than the wall.

You need those openings to secure the mount. When you bolt the wall mount in place, the tails open up, making the plugs harder to remove. Secure the plugs into the wall with a hammer and chisel. Place the tip of a chisel against one of the bolts. Give the chisel's handle a couple of good whacks to push the bolt into the wall. Keep hammering until the bolt is flush with the wall. Then, repeat this with the remaining bolts. Make sure the bolts are level with the wall, or else the dish's mount won't anchor properly.

Place the metal plugs and hammer them into the wall. Your dish will come with a set of plugs that serve as wall anchors. Position them, so their open end faces out from the wall. That opening is for bolting the wall mount in place. After pushing the plugs into the holes, tap them in with a hammer and chisel.

They are what anchors the mount to the wall or ceiling. If they are loose, your dish could end up crashing to the ground!

Bolt the mount onto the plugs in the wall. Position the mount back on the wall, lining up the plate's holes with the pilot holes you drilled. Fasten the bolts by using a cordless screwdriver. Make sure the mount feels secure in the wall before you move on. If you're sure they are in correctly, take them out and recheck the plugs.

Cap each bolt with a metal washer and locking nut. These components prevent the bolts from coming back out of the wall. Slide the washers on first, which are flat metal disks that help the nuts work properly. Then, add the nuts and turn them clockwise with a wrench until they feel tight and no longer move. Be careful not to overtighten the nuts. Stop twisting them when they become hard to move. As long as they are not loose, the mount will also stay in place.

Part 2. Attach the antenna bracket to the low noise block LNB arm. Your dish will most likely come with a flat metal plate to connect the satellite dish to the L-shaped LNB arm and other components. Position the plate, so the prongs are on the left and right, facing you. Hold the LNB arm between the prongs with the tail end extending out past the plate's opposite side. The exact installation process, including the bolts' size, may vary a little depending on the dish you have.

Refer to the owner's manual for more specific instructions. Clip the antenna adjustment panel over the plate's prongs. Nik and his team can link your TV, Satellite Box and other Boxes to your broadband router for access to all TV players and Apps for your on-demand content from the internet.

BT customers can order a free replacement. Click on the link to read more in our Freesat Installation Service page. Digital Direct are specialists at supplying and installing a range of high-end satellite TV systems, which are capable of receiving European satellite TV. If you are considering this as an alternative to the Sky Pub service then read the latest legal update on our European Satellite page. Petra, Harborne,19 th September. We were very pleased when we had to have a new satellite dish erected due to wear and tear Richard the engineer who came was excellent and did a very good job with no fuss or bother.

We would thoroughly recommended your company to anyone. Mr Amos, Quinton, 7 th January Efficient and polite service. Cured poor satellite signal problem, would recommend this company. Don, Bewdley, 13th May After the recent high winds I thought I would have to wait at least a few days for someone to come to repair our Freesat, but no, within 3 hours of my call the engineer was at our house and the problem sorted. Both the call receiver and engineer were amazing, polite and happy to help, thank you Direct Digital will definitely recommend.

Wendy, Bromsgrove, 1st March First Class and professional. I have used Digital Direct twice once to move a satellite dish , and recently to replace a snapped pole on a TV antenna I am an enthusiast with TV and radio the work on both occasions was carried out to a very high standard and a very good price.

Paul, Bromsgrove, 27th February Fantastic service. Polite, friendly, efficient staff. They even managed to come and sort my satellite dish on the day I called them. Would definitely recommend this company. Morag, Coventry, 30th January